CN
EN
DE
FR
ES
???
How to repair the leakage of shower
Time : 2021-10-15 0:00:00 Hits : 2805
1. When showering with a flower shower, it is found that the outlet water is not a jet of fine water, but a coarse water column in some places.
There are two reasons why the fine water of the shower becomes the coarse and fine mixed water. One may be that the water spraying mode of the shower is adjustable. If so, rotate and adjust the nozzle; If it is not adjusted, it may be caused by too much dirt in the nozzle. Open a small round cap in the middle of the nozzle with a small flat screwdriver, screw down the screw with a plum blossom screwdriver, open the shower, rinse with clean water, or brush the shower hole with a toothbrush, and then install and return it.
2. Water leakage at the connection between hose and nozzle
The causes of water leakage may be improper installation, deformation of rubber ring, uneven or too thin outlet pipe joint, or mismatch between hose and nozzle. Select the appropriate hose and nozzle according to the specification, replace the rubber ring and reinstall it.
3. Low water temperature
When using, it is found that the water temperature is low, which may be due to insufficient power of the water heater and the temperature is not adjusted in place. At this time, you can adjust the temperature control button or buy a water heater with large water output.
4. Shower coating leakage repair
Carefully observe whether the leather ring of the shower head falls off. If so, you can adjust it with a toothpick or a relatively small thing, and then try with water. If the electroplating on the surface of the shower falls off, you can only replace it, because this electroplating technology cannot be processed by yourself at present.
5. Repair of sprinkler head steering ball
If there is a problem with the steering ball of the shower head, first screw the shower head off the steering ball ring, find out the inner sealing ring or O-ring, and replace it. After the sealing ring is installed, screw the shower head back to its original position and try with water.
6. Repair the connection of shower head handle
If there is a problem with the handle connection of the shower head, you should go to the market to buy a faucet and shower hose of the same specification, and it is best to replace the old sealing ring and reinstall it. First unscrew the shower head and handle from the hose, then clean the thread on the shower head handle with clean water, and tie special tape for water pipe or apply special adhesive for water pipe around. Then tighten the head of the shower in a circular way and remove the excess tape and adhesive.
7. The amount of water decreases
When the water pressure is normal, if the water output is reduced or even the water heater stalls after using for a period of time, you can gently unscrew the screen cover at the water outlet of the shower, and then remove the impurities, which can generally be restored as before.
There are two reasons why the fine water of the shower becomes the coarse and fine mixed water. One may be that the water spraying mode of the shower is adjustable. If so, rotate and adjust the nozzle; If it is not adjusted, it may be caused by too much dirt in the nozzle. Open a small round cap in the middle of the nozzle with a small flat screwdriver, screw down the screw with a plum blossom screwdriver, open the shower, rinse with clean water, or brush the shower hole with a toothbrush, and then install and return it.
2. Water leakage at the connection between hose and nozzle
The causes of water leakage may be improper installation, deformation of rubber ring, uneven or too thin outlet pipe joint, or mismatch between hose and nozzle. Select the appropriate hose and nozzle according to the specification, replace the rubber ring and reinstall it.
3. Low water temperature
When using, it is found that the water temperature is low, which may be due to insufficient power of the water heater and the temperature is not adjusted in place. At this time, you can adjust the temperature control button or buy a water heater with large water output.
4. Shower coating leakage repair
Carefully observe whether the leather ring of the shower head falls off. If so, you can adjust it with a toothpick or a relatively small thing, and then try with water. If the electroplating on the surface of the shower falls off, you can only replace it, because this electroplating technology cannot be processed by yourself at present.
5. Repair of sprinkler head steering ball
If there is a problem with the steering ball of the shower head, first screw the shower head off the steering ball ring, find out the inner sealing ring or O-ring, and replace it. After the sealing ring is installed, screw the shower head back to its original position and try with water.
6. Repair the connection of shower head handle
If there is a problem with the handle connection of the shower head, you should go to the market to buy a faucet and shower hose of the same specification, and it is best to replace the old sealing ring and reinstall it. First unscrew the shower head and handle from the hose, then clean the thread on the shower head handle with clean water, and tie special tape for water pipe or apply special adhesive for water pipe around. Then tighten the head of the shower in a circular way and remove the excess tape and adhesive.
7. The amount of water decreases
When the water pressure is normal, if the water output is reduced or even the water heater stalls after using for a period of time, you can gently unscrew the screen cover at the water outlet of the shower, and then remove the impurities, which can generally be restored as before.
Prev:Sorry! no data.Place click Go Back
